Chemical Engineering

The impact of ultrasound (US) on membrane filtration and cleaning were studied and compared at various operating parameters of nominal pore sizes of 10 and 100 kDa membrane, trans-membrane pressure (TMP) of 100 and 140 kPa, and US frequencies of 20 kHz and 40 kHz. An average of 15%–20% increase of permeability was observed when US (20 kHz) was applied to assist membrane filtration on 10 kDa membrane and 100 kPa trans-membrane pressure (TMP). However, an insignificant improvement was observed in the case of larger pore size membrane at higher TMP (140 kPa). US also augmented the membrane cleaning process effectively. Lower frequency 20 kHz US exhibited a higher flux recovery (>90%) than the high frequency 40 kHz (59%) using the 10 kDa pore size membrane with US-assisted membrane cleaning. Important factors influencing optimization of US effectiveness lie heavily on its configuration and operation. The experimental results as supported with SEM images demonstrate that US-assisted filtration and cleaning are most effective when membrane pore size, US frequency, and TMP are lower.

Modern membrane technologies are useful for enhancing the concentration of phenolic antioxidants in olive mill waste water (OMWW) to produce concentrates with valuable applications in functional foods. Three types of OMWW concentrates, each with different levels of solute concentration and purity, were obtained from a single OMWW batch and dissolved in two extra virgin olive oils to achieve saturated solutions. Three addition levels were considered. Accelerated aging testing of the oils was performed at 60 °C and the samples were analyzed after two, four, and 6 weeks of aging. D-optimal design was used to select the 26 experiments that allowed the evaluation of the influence of the different variables on oil stability. The addition of OMWW concentrates resulted in a significant increase in the Radical Scavenging Activity (RSA) of the olive oils. Under these mild experimental conditions, the moderate formation of fatty acid hydroperoxides was probably masked by interfering compounds.

In this paper, a study on the batch processing and characterization of microcellular foamed high-density polyethylene (HDPE/iPP) blends is reported. A microcellular plastic is a foamed polymer with a cell density greater than 109 cells/cm3 and fully grown cells smaller than 10 µm. Recent studies have shown that the morphology and crystallinity of semicrystalline polymers have a great influence on the solubility and diffusivity of the blowing agent and on the cellular structure of the resulting foam in microcellular batch processing. In this research, blends of HDPE and iPP were used to produce materials with variety of crystalline and phase morphologies to enhance the subsequent microcellular foaming. It was possible to produce much finer and more uniform foams with the blends than with neat HDPE and iPP. Moreover, the mechanical properties and in particular the impact strength of the blends were significantly improved by foaming.
(citation # 293)

AbstrAct It is a current concern in the wood preservation field to avoid the use of toxic chemicals and develop new technologies based on low environmental impact agents and sustainable principles. Under this expectation, an intended state-of-the-art is introduced on the application of natural products such as traditional tar and wood oils as well as tannins and plant extracts. A particular revision to heartwood chemical components is offered. The combined methods of using natural and chemical components are reviewed, considering as outstanding the mixtures of natural organic constituents with cooper and boron salts that seem to be under encouraging experimentation. Fungicides and anti-termite applications are commented as well the leaching problem of inorganic salts. Chemical modification of wood structure through the formation of adducts and the treatment with nanomaterials are promising tools that will change the actual view and performance of wood preservation techniques. resumen Una de las prioridades actuales en el campo de la preservación de madera es evitar el uso de materiales tóxicos, desarrollando nuevas tecnologías fundamentadas en principios sustentables y empleando agentes de bajo impacto ambiental. Con esta expectativa se plantea una revisión del estado del arte sobre la aplicación de productos naturales, tales como taninos, alquitrán, aceites y extractos vegetales. Se presenta en particular una revisión sobre los componentes químicos contenidos en el duramen de maderas naturalmente resistentes. Se analizan los métodos combinados de ingredientes naturales y químicos, resaltando las mezclas de componentes naturales orgánicos con sales de cobre y boro que parecen representar una opción experimental confiable. Se comentan también las aplicaciones fungicidas y anti termitas, así como los problemas de lixiviación de sales inorgánicas. Opciones como la modificación química de la madera vía la formación de aductos y por tratamiento con nanomateriales son procesos promisorios que cambiaran eventualmente la manera de ver y aplicar la tecnología actual de preservación de maderas.